HEAT STABILIZED UNREINFORCED NYLON 46 - TE 341 | ||||
STANYL® TE 341 | ||||
DSM Engineering Plastics - Stanyl® Heat Stabilized Unreinforced Nylon 46 - TE 341 | ||||
High temperature nylon, which bridges the price performance gap between traditional nylons and high performance materials. Nylon 46 has excellent short and long term heat resistance, high stiffness at elevated temperatures, high creep resistance, outstanding toughness, excellent fatigue behavior, good chemical resistance, and higher continuous-use temperature. Nylon 46 is translucent off white in color. | ||||
APPLICATIONS | ||||
Fasteners – Bearings – Cams – Gears – Printed Circuit Board Hardware – Washers – Spacers – Insulators – Electronic Components – Bushings – Wiring Clips – Cable Clamps – Hose Clamps. | ||||
Properties | ||||
Physical | Units | Test Method | Value | |
Density | g/cc | ASTM D792 | 1.18 | |
Melting Point | °F | ASTM D3417 | 563 | |
Heat of Fusion | kJ/kg | 105 | ||
Specific Heat Cp @ 248°F | kJ/kg.K | 2.1 | ||
Thermal Conductivity (method A) | W/K.m | 0.3 | ||
Poisson ratio (not for GF) | 0.37 | |||
Water Absorption at Equilibrium @ 73°F/50% RH | % | 3.7 | ||
Water Absorption 73°F/24hr, 3.2mm | % | ASTM D570 | 2.3 | |
Mechanical | Units | Test Method | DAM | 50% RH |
Impact Resistance Izod Notched @ 73°F | J/m | ASTM D256 | 100 | 400 |
Impact Resistance Izod Notched @ -40°F | J/m | ASTM D256 | 50 | |
Tensile Strength at Yield @ 73°F | MPa | ASTM D638 | 100 | 40 |
Tensile Strength at Break @ 73°F | MPa | ASTM D638 | 80 | 65 |
Elongation at Break @ 73°F | % | ASTM D638 | 30 | 280 |
Tensile Modulus @ 73°F | MPa | ASTM D638 | 3,000 | 1,000 |
Flexural Modulus (4 point) @ 73°F | MPa | ASTM D790 | 3,500 | 1,200 |
Flexural Modulus (3 point) @ 73°F | MPa | ASTM D790 | 3,200 | 1,000 |
Flexural Modulus (3 point) @ 248°F | MPa | ASTM D790 | 800 | |
Flexural Strength (3 point) @ 73°F | MPa | ASTM D790 | 150 | 50 |
3.5% Flexural Strength (3 point) @ 73°F | MPa | 100 | 30 | |
Creep Modulus 1000 h@ 1% strain @ 73°F | MPa | ASTM D2990 | 750 | |
Creep Modulus 1000 h@ 1% strain @ 194°F | MPa | ASTM D2990 | 890 | |
Creep Modulus 1000 h@ 1% strain @ 248°F | MPa | ASTM D2990 | 710 | |
Creep Modulus 1000 h@ 1% strain @ 284°F | MPa | ASTM D2990 | 660 | |
Shore Hardness Scale D @ 73°F | ASTM D2240 | 85 | 79 | |
Rockwell Hardness Scale R | ASTM D785 | 123 | 107 | |
Thermal | Units | Test Method | DAM | 50% RH |
HDT A at 1.8 Mpa | °F | ASTM D648 | 320 | |
Vicat at 49N/248°F Unannealed | °F | ASTM D1525 | 550 | |
Peak Temperature 1 min. | °F | >428 | ||
Continuous Use Temperature 5,000 hours | °F | 311 | ||
Coefficient of Linear Thermal Expansion | 1/(K. 105) | ASTM D696 | 7.3 | |
Flammability @ 1.6 mm | UL94 | V-2 | ||
Electrical | Units | Test Method | DAM | 50% RH |
Dielectric Strength @ 73°F | kV/mm | ASTM D149 | 65 | 45 |
Volume Resistivity @ 73°F | ohm-cm | ASTM D257 | 1016 | 1014 |
Surface Resistivity @ 73°F | ohm | ASTM D257 | 1015 | 1013 |
Dielectric Constant @ 73°F | ||||
@ 50 Hz | ASTM D150 | 4.3 | 13.3 | |
@ 1 kHz | ASTM D150 | 4.2 | 9.4 | |
@ 1MHz | ASTM D150 | 3.8 | 5.0 | |
Dissipation Factor @ 73°F | ||||
@ 50 Hz | ASTM D150 | 0.008 | 0.15 | |
@ 1 kHz | ASTM D150 | 0.017 | 0.21 | |
@ 1MHz | ASTM D150 | 0.015 | 0.11 | |
Comparitive Tracking Resistance CTI @ 73°F | V | ASTM D3638 | 600 | |
Electrolytical Corrosion 104°F/92% RH | class | AN 1,2 |